Advantages Of Foam

Foam concrete is a modern building material, used as an effective insulation and structural elements (in units) for low-rise building. Its advantages are obvious and quite visible. First of all, captivates its environmental friendliness. Foam concrete does not contain harmful chemicals. It consists of cement – mineral organic matter.

As for water resistance, this quality is far superior autoclaved aerated concrete. The surface of the foam has a closed cell structure, and therefore absorbs very little moisture. Durability of foam under normal operating conditions is not limited. Over the years, it becomes only stronger. In addition, it has low thermal conductivity. For low-density thermal insulation foam concrete does not yield polystyrene. But unlike the latter it does not eat rodents. The positive properties can be attributed to the monolithic.

Flooded into the brickwork under pressure, foam fills all the cracks. Congealing, he further connects the outer and inner surfaces. In this case the wall does not lose its ability to "breathe". In addition, non-combustible foam concrete, which distinguishes the construction of concrete houses. The exact cost of building the foundation and building blocks of foam can calculate according to the selected home construction.

Brick Fireplace

Fireplaces great variety of systems, but this article deals with one of the most simple fireplace – brick, which the owners themselves can add up in suburban or garden house. What are the requirements to the fire? – Fireplace not should smoke – fireplace must have a good warm up the air – fireplace must be beautiful and fit into the interior. Dimensions Dimensions of the furnace combustion of sizing fireplace with his hands begin with the definition area and volume of the room where the fireplace will be arranged. For example, a porch or a room country house with area of 10, 15 or 20 meters, ceiling height 3.3-3.5 meters. Volume of the room will be respectively 35, 50 or 70 cubic meters. m. The area of the flue fireplace openings for these volumes relates to the area of the premises as 1:50 – 1:70 and will be respectively 0.2, 0.3, 0.4 square meters.

m. We define the height and width of the fireplace flue openings, so-called portal firebox. There also exists dependence – for the small fireplace that will be 2:3 (height to width). – Podorbnee here. That is, for our fireplace the size of the portal will be respectively: – 0.2 square meters. m – 36h45 cm – 0.3 sq. km.

m – 44h67 cm – 0.4 sq. km. m – 52h77 cm depth of the firebox fireplace with a tall portal must be in respect of 1:2-2:3, this size is also necessary to observe, as most of the depth reduces the heat in the room, and the smaller is smoke. In our case, this depth will be: – for section 0.2 square meters. m: 18 – 24 cm – for section 0.3 square meters. m: 22 – 30 cm – 0.4 kV for the cross section. m: 26 – 35 cm Now, we have defined the dimensions of the firebox of the fireplace (see Fig. 1). Fireplace smoke hole depends on the size of the firebox opening and must be 8-15 times lower, respectively, it is: 0.02, 0.03 and 0.04 sq. km. m. If the chimney brick chimney, these dimensions are 14X14 and 14X27 correspondingly see if the chimney flue chimney with a circular, its diameter ranges from 8 to 14 cm in height define the chimney, in our case it should be 4-5 meters. The device inserts Fig. 2 The device unit firing furnace for better heat reflecting ability of the fireplace firebox preferably internal walls meet at an angle to the side outward, and back tilted forward, starting with 1 / 3 of the height above the firebox fireplace smoke chamber is arranged between them produced a cornice, which is called a 'pass'. Pass prevents the removal of soot and sparks from the fire outside and smoke inside premises. His device is shown in poryadovkah. So, we figured out basic technical parameters of the fire, will now determine its overall size. We arranged to meet our fireplace brick, hence, all sizes should be given to the unit masonry. Brick has a size of 6,5 X12X25 cm, and masonry seam about 0.5 cm

Desktop Design

Nowadays, more and more talk about one, and it turns on all at once. That these lines are no exception, running in front of his artistic imagination, to admit. For your design idea article will be framed in a chic prints decorate the walls of words and business, as the original poster or a poster. … Cheap design, in my opinion, the term is not acceptable at all, even if you hang a single picture in a shoe shop. Simply place does not is still in the same place does not appear the best picture.

And whoever came to your door, notice the picture and to forget what came. So what is design, interior space. In my opinion, this well-chosen combination of lines and colors. That is, in other words I’m talking about the original idea more than a large investment. For taste is always born out of modesty. What replacement cost.

There are many ways to simply and tastefully arrange new office. One of them is the posters and placards. Correctly matched a picture or other image in conjunction with the composite processing and stylistic change the image’s interior can give a great result and at the same time to save your budget. When you print posters or placards on the canvas in most cases do not even need baguette design work. Enough subframe and high-quality stretch canvas, and a protective varnish coating make a poster almost for ever. The budget is certainly an important component in the design of the room, elegance and taste the same way no one has canceled, but there is another side about which is often overlooked: it is a semantic idea. Making paintings, posters, Desktop, as well as selected songs Verbal, printed on canvas, silently telling about the company. It is literally on the threshold, and most importantly without the necessary intervention by staff. And so the empty walls of your new office … … and it is always interesting.

Methods Of Forming Refinishing

Formation of coatings (PC) – is the curing (drying) coatings (paints), which takes place in specific time-temperature conditions, which is one of the most important stages of technological the process of staining, a significant impact on physical and mechanical, safety, and in some cases, decorative properties of PS. The technology of coatings distinguish natural and artificial drying. Natural drying carried out under normal conditions (for example – drying enamel PF-115), energy-intensive artificial drying, process is implemented using a special, sometimes technically complex equipment. So natural drying paint is always preferable, and in many cases due to the specific technology, the only possible. This is particularly relevant curing method for coloring large products on open sites, in rooms with PC repair.

To cure the in vivo requires a certain, for most paints an extended period of time. Therefore, methods for accelerating curing of in vivo is of considerable practical interest. They are based on the use of quick-drying paint consisting of film formers, such as acrylic or perchlorovinyl. To reduce drying time results in chemical or physical modification of epoxy, alkyd and urethane oligomers cured under natural conditions in a long time. For example, the combination of epoxy resin oligomer perchlorvinyl cuts drying time of epoxy coatings with 24 to 1 h at 20 C, akriluretanovye materials cured under normal conditions for 2 – 4 pm Currently, various manufacturers developed a number of coatings, fast drying in natural conditions. This – epoxy-vinyl enamel EP-1294 EP-1267 EP-1236, "Evikor"; akriluretanovye enamel AU-1518 "Universal Luxury" AK-1511 "Raznotsvet" as well as widely known glyptal materials – primer GF -021, and others. And is characterized accelerated drying time under natural conditions, these coatings can be applied not only to paint outdoors or in repair technology, but also on the production of conveyor lines. Using the dilution of the material more volatile solvents, reducing the thickness of layer applied, the number of layers, the use of catalysts, cure, more active hardeners and accelerators are also resulting in intensify the process of curing the PC in the wild. GA Mironov (JSC "Research Institute of LCP")

Coating Materials

To date, ceramic – is one of the most commonly used coating materials. This is a magnificent, almost perfect artificial stone, a beautiful, durable and very practical. Today, porcelain is often apply when facing repair work, as they adorn the kitchen and bathrooms, and nice trim halls, corridors, rooms and other premises. Still, finished granite facades, paths in the garden, and more. Not less good for granite fireplaces, swimming pools, stairs, and much more, in one word – it's just a great versatile stone.

Much-loved and widely applicable granite today due to high indicators of quality, strength, durability and resistance to moisture and frost. The strength of good porcelain knows no boundaries, which precludes it as a damaged or scratched, and over time, this excellent Stone does not deteriorate. With the help of granite stone, today designers are creating beautiful interiors and design, thanks to the variety of textures and richness of color and tone colors of this material. Beautiful shiny ceramic with a shiny surface – Semi, especially polished now widely used for finishing and decorating indoors, in areas where the least amount of negative for this stone factors: such as moisture, making a slippery tiles, and a sharp drop in temperature. Granite stone on several indicators of better natural stone, in particular, it exceeds it at the price and durability, it is more accessible In this regard, natural stone. The most affordable granite can be called domestic product, as well as porcelain from China. Ordering ceramic wholesale from China, we can not expensive, but it is really beautiful and luxurious design the interior.

Japanese Curtains

Looking for a fairly complex system of Japanese curtains, many a question – is it possible to make a Japanese curtains with his hands? You can, after all is not as difficult as it may seem at first glance. The main thing – to know some of the nuances and details of their manufacture. Of course, you can order blinds in the studio, but if you have some free time, and thus you are interested in sewing, you should not refuse the pleasure to practice self- Japanese manufacturing curtains – it's very entertaining. Japanese curtains or as they are in another call, the Japanese panel, are made as of the dense and thin translucent materials. About the figure we can say following: due to limited width of the surface image in any case should not be very wide. The rest – a matter of taste. So, you can use fabrics with patterns in the Oriental style: Arabic characters, kanji, traditional Ornaments, Chinese dragons, etc.

This is the traditional approach. With respect, the latest fashion trends, it is, above all, abstract paintings, as well as black and white checkerboard style. Next, we finally get down to practical part of the question – "How to sew curtains Japanese?". Nuances to keep in mind: – The Japanese paintings panels shall not exceed sixty inches in width. This length is the standard, due to the fact that, as a rule, used rails, designed by her – on the top edge of the curtains should not be assembly – Do not use different decorations, accessories and pickup. Now directly on the processing of fabrics. Need to carve out straight strips of fabric width of 60 inches, as well as allowances for podgibku and shrinkage.

After that, begin to treat the side seams and lower future curtains. Since the low process kuliskoy, allowances it does not zastrachivat recommended. After all this it follows otutyuzhivaem osnorovyvaem and the upper edge of the canvas. Recommendation: The most likely to fully close the window, you'll need a few panels. Therefore osnorovku should be carried out immediately several paintings (but not more than four). Calculation of the length of the panel about osnorovki – herself blind in finished form, plus leave a little under a Velcro (Velcro) 1-2 cm. When you buy machinery for the Japanese panel, pay attention to the upper part, which is attached directly onto the ledge. This part is a bar with the correct (hard) part of the Velcro. That is why in the manufacture of Japanese curtains and should be used initially Velcro. All finished panel after sewing on Velcro should end once otutyuzhit, as the Japanese curtains straight lines side seams play a crucial role. After the final scenes of paddles in the bottom panels Threading weighting, the top edge of the curtain is attached to a special holder (the soft part is mounted on a rigid part of the Velcro). And yet – you're done! From now on, Japanese curtains, made with his own hands, will please your eye! Source: flexart-studio.ru – sewing Curtains on order